The Bar Profit Guys
$0.00 (0) My Cart MY CART
Clear Beer Faucet Extender for Standard Faucets
Click to Enlarge Images

Clear Beer Faucet Extender for Standard Faucets STOP POURING YOUR PROFITS DOWN THE DRAIN

The quantity pricing below reflects a per unit price without upgrades if available.

Reg. PriceWeb Special6+12+
$20.99 ea$10.99 ea$9.99 ea$8.99 ea
+ Click to Add Another Item
Subtotal of Item(s):
  • Description
  • Instructions
  • Videos
  • Related Products

The Beer faucet extender eliminates the creation of unwanted foamy beer by minimizing flow turbulence with a bottom-of-the-container fill method. The beer head formed is always a consistent 1/2 to 1 inch thick.

Here is how it works: The Beer faucet extender slips into the end of your existing beer faucet. It moves the dispense point closer to the bottom of the container, decreasing the agitation of the beer during the pour to eliminate excessive foaming.

This faucet extender is available in two lengths ... a 3" extender for $10.99 and a 5-1/2" extender for $13.99. The shorter extender is often used when glasses, mugs, or cups are the more popular beer containers. The longer extender is ideal for establishments that serve more pitchers or growlers.

Beer Faucet Extenders easily attaches to the end of a standard beer faucet to help bartenders pour draft beer with less foam. Be aware that Bottom-Pour will not fit into the MicroMatic 304, Perlick 500-series, 600-series, or Stout beer faucets.

Bottom-Pour Beer Faucet Extender Guide Chart

   Standard Faucet    

MicroMatic 304 Series

Perlick 500 Series
Bottom Nut 7/8" Across

Perlick 600 Series
Bottom Nut 1-1/8" Across

       Stout Faucet       

This ingenious device should pay for itself in less than 12 glasses of beer by reducing the creation of foamy beer that inevitably gets poured down the drain. The Beer Faucet Extender is so effective it has been implemented in major restaurant chains and was promoted on Spike TV's Bar Rescue program.

IMPORTANT TIP BEFORE ORDERING THE LONGER BEER FAUCET EXTENDER: Add 5-1/2" to the bottom of the beer faucet using a pencil or straw and see if there is enough room above the drip tray to insert your glasses and pitchers before pouring. It typically requires 5 inches of space to easily move your glasses and pitchers in and out from under the beer faucet. If there is not enough space with the 5-1/2" extender, you will need to order the shorter 3" extender.

Quantity discounts are available for minimum purchases of 6 and 12 extenders. Note that the Beer Faucet Extenders will not prevent foaming created by beer dispensing system problems like warm beer temperature or incorrect gas pressure.


1. Hold the Beer Faucet Extender with the slot on top facing out towards you below the beer faucet.

2. Insert the fitting end into the beer faucet and gently push in the faucet.


1. Place the glass under the Bottom-Pour faucet extender. The extender should be as close as possible to the bottom of the glass, pitcher or growler. The edge of the extender should also be close to the side of the glass.

2. Open the beer faucet handle and pour beer keeping the Beer extender in the glass until the pour is complete.

3. With the Beer Faucet Extender, you may be able to pour beer faster by increasing the applied gas pressure to the keg. Before doing this, check with your beer distributor to make sure you have the proper blend of gas to prevent over-carbonation of the beer.

Reg. PriceWeb Special5+10+20+
$2.25 ea$1.95 ea$1.85 ea$1.75 ea$1.65 ea
Keep unwanted pests from contaminating your beer faucets. No more stuffing your taps with rolled napkins, strips of cellophane or shaved corks. The polyurethane Bug Plug will keep fruit flies out of the draft beer faucets when they are not in use.
Reg. PriceWeb Special6+12+
$3.95 ea$2.95 ea$2.75 ea$2.50 ea